Universal dimmer switch minimum load only 4W - Dimmer flush mounted 4...400VA EUD61NPL-230V
EUD61NPL-230V
61100832
4010312109618
EAN/GTIN
DE 30298319
WEEE
Safety and hazard information
Please note that electrotechnical work may only be carried out by qualified electricians or under their guidance and supervision. Observe any deviating country-specific electrical installation standards and regulations and seek advice from a local electrician.In addition, observe more current safety instructions and regulations for the products on the manufacturer's side or the product descriptions and installation instructions on the manufacturer's side.
Devices with a connected load of > 380V/400V require a heavy current connection and may only be connected by an approved electrical company. Devices with a power rating > 12kW require the approval of your grid operator (Germany, other countries may differ).
Please note that electrotechnical work may only be carried out by qualified electricians or under their guidance and supervision. Observe any deviating country-specific electrical installation standards and regulations and seek advice from a local electrician.In addition, observe more current safety instructions and regulations for the products on the manufacturer's side or the product descriptions and installation instructions on the manufacturer's side.
Devices with a connected load of > 380V/400V require a heavy current connection and may only be connected by an approved electrical company. Devices with a power rating > 12kW require the approval of your grid operator (Germany, other countries may differ).
read more
show less
Universal dimmer switch minimum load only 4W EUD61NPL-230V composition other, touch operation,...
more
Universal dimmer switch minimum load only 4W - Dimmer flush mounted 4...400VA EUD61NPL-230V – Eltako – 61100832 – 4010312109618: Universal dimmer switch minimum load only 4W EUD61NPL-230V composition other, touch operation, dimming leading edge, dimming trailing edge, load type universal, light value memory, can be used with button, mounting type flush-mounted, type of mounting with screw, material plastic, material quality thermoplastic, halogen-free, surface untreated , surface design matt, color blue, rated voltage 230 ... 230V, control voltage 230 ... 230V, rated power 4 ... 400VA, connection type screw terminal, wire cross section 4 ... 4mm², device width 45mm, device height 45mm, device depth 18mm, min Depth of the device box 18mm, without N-connection, power MOSFET up to 200W. Standby loss only 0.5 watts. With control inputs for light buttons and light switches. Minimum brightness, operating mode and dimming speed adjustable. For flush mounting. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R and C loads up to 200W, depending on the ventilation conditions. Dimmable ESL and 230V LED lamps in trailing edge operating mode up to 200W or in leading edge operating mode up to 40W, depending on the ventilation conditions. In the case of dimmable 230V LED lamps, which also light up slightly when switched off, a GLE base load element must be connected in parallel with the lamp. L loads (inductive loads, e.g. wound transformers) must not be connected. Switching at zero crossing with soft on and soft off to protect the lamp. Control voltage, supply voltage and switching voltage 230V. Minimum load 4W. Short control commands switch on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level is saved when the device is switched off (memory). Memory can be switched off by turning the upper rotary switch three times to the right stop (max). Then ESL can also be switched. Switch the memory back on (factory setting) by turning it three times to the left stop (min). In the event of a power failure, the switching position and the brightness level are saved and, if necessary, switched on when the supply voltage returns. Automatic electronic overload protection and over-temperature shutdown. The minimum brightness (fully dimmed) can be set with the upper % rotary switch. The lower dimming speed rotary switch is used to select between the trailing edge (P-AB) or leading edge (P-ON) operating mode, the dimming speed is set and the duration of soft on and soft off is changed at the same time. In the event that light switches cannot be replaced by light buttons, there is a separate control input for light switches: if the closed switch is briefly opened again, it is dimmed until it is briefly opened again. A change in the dimming direction takes place automatically at the two vertices. In addition, the direction can be changed by briefly opening the switch twice. With children's room circuit (only when controlled with a button): When switching on by pressing the button for a longer period of time, it is switched on with the lowest brightness after approx. With snooze function (only when controlled with a button): A double pulse dims the lighting from the current dimming setting down to minimum brightness and then switches it off. The maximum dimming time of 60 minutes depends on the current dimming setting and the set minimum brightness and can be shortened accordingly. You can switch off at any time during the dimming process by briefly pressing the button. A long press during the dimming process dims up and ends the snooze mode. Without N connection, therefore suitable for mounting directly behind the light button or light switch, even if no N line is available.
...
more
Compilation | other |
Of operation | Tip button |
App control via Bluetooth | no |
Dimming Phase control | yes |
Dimming Phase section | yes |
Series dimmer | no |
Load type | universal |
Extension input | no |
Light value memory | yes |
Suitable with button | yes |
Usable with motion detector | no |
Suitable with presence detector | no |
Usable with timer / timer | no |
Suitable with radio button | no |
Usable with IR button | no |
Mounting | Flush |
Mounting | Fastening with screw |
Material | Plastic |
Material quality | Thermoplastic |
Halogen free | yes |
Surface protection | untreated |
Execution of the surface | frosted |
Colour | blue |
Transparent | no |
Nominal voltage | 230V |
Control voltage | 230V |
Rated capacity resistive load | 200 W |
Rated capacity capacitive load | 200 VA |
Max. switching capacity LED | 200 W |
Connection | Screw terminal |
Core cross-section | 4 mm² |
Device width | 45 mm |
Device height | 45 mm |
Device depth | 18 mm |
Min. depth of the device socket | 18 mm |
Compatible with Apple HomeKit | no |
Compatible with Google Assistant | no |
Compatible with Amazon Alexa | no |
IFTTT support available | no |
Cookie settings
This website uses cookies that are required for the technical operation of the website and always stored. Other cookies that enhance convenience when using this website, or that are intended for direct marketing or to simplify interaction with other websites and social networks, are only stored with your consent.
Configuration
Technically required
These cookies are required for the basic functions of the shop.
Accept all cookies
Amazon Pay
CSRF token
Cookie settings
Currency change
Customer recognition
Customer-specific caching
FACT-Finder tracking
Individual prices
Reject all cookies
Selected shop
Session
Wish list
Device recognition
Saferpay payments
PayPal payments
IP2location
Listing settings
Trustami
Wishlist
TagManager
Statistics and tracking
Google analytics
Partner program
Custom tracking