N000402
DE 31640810
WEEE
Safety and hazard information
Please note that electrotechnical work may only be carried out by qualified electricians or under their guidance and supervision. Observe any deviating country-specific electrical installation standards and regulations and seek advice from a local electrician.In addition, observe more current safety instructions and regulations for the products on the manufacturer's side or the product descriptions and installation instructions on the manufacturer's side.
Devices with a connected load of > 380V/400V require a heavy current connection and may only be connected by an approved electrical company. Devices with a power rating > 12kW require the approval of your grid operator (Germany, other countries may differ).
Please note that electrotechnical work may only be carried out by qualified electricians or under their guidance and supervision. Observe any deviating country-specific electrical installation standards and regulations and seek advice from a local electrician.In addition, observe more current safety instructions and regulations for the products on the manufacturer's side or the product descriptions and installation instructions on the manufacturer's side.
Devices with a connected load of > 380V/400V require a heavy current connection and may only be connected by an approved electrical company. Devices with a power rating > 12kW require the approval of your grid operator (Germany, other countries may differ).
read more
show less
Note: The Power over Ethernet supply is standardized acc. to Standard PoE (IEEE 802.3af) and...
more
KNX IP Router PoE N000402 – EIBMARKT: Note: The Power over Ethernet supply is standardized acc. to Standard PoE (IEEE 802.3af) and integrated via RJ45. We can recommend a PoE Ethernet Switch from Netgear, e.g. FS108P. The device disposes of 8 ports, four of which are equipped with Power over Ethernet (IEEE802.3af, 48 VDC). The IP Router, for example, can be connected to one of these four ports. As an alternative, power supply can be provided by means of screw connecting terminals at the upper side using a separate power supply unit (12-24V DC) or transformer (12-24V AC). Parallel power must be avoided! Caution when using managed Switches (Cisco or similar): With some Switches there can problems with the standard settings and the IP devices are not recognized. In this case make the following adjustment at the Switch: Full-Duplex-Mode Digit rate: 10 Megabit/s A blinking Ethernet LED at the IP Router or IP Interface indicates an existing link i.e. the digit rate and the mode have been set correctly. The KNX IP Router is capable of Routing and Tunnelling at the same time, i.e. ETS programming (Tunnelling) and coupler function (Routing) are possible in parallel. KNXnet/IP Tunnelling allows only one connection by means of the KNX IP Router interface function to the bus. With Routing several devices can access the bus simultaneously. Routing is preferably used when the KNX IP Router is applied as line or area coupler. However, it can, for example, also be used for the connection of a visualization application. Applications: For ETS-programming a KNX IP interface that supports only the tunnelling protocol is sufficient (KNX IP interface instead of KNX IP Router). However, the ETS also supports programming by means of the routing protocol. If you want to connect visualizations, it must be verified which protocol the respective software supports. So, the current Gira HomeServer supports nothing but the routing protocol. For simultaneous access of several applications the routing protocol is required (KNX IP Router), while one application can make use of the tunnelling protocol. Remote internet access is always achieved via tunnelling protocol. KNX/EIB IP Router IP-Router / Interface between LAN and EIB/KNX bus Application area The KNXnet/IP router allows forwarding of telegrams between different lines (as EIB KNX area/line coupler) through a LAN (IP) as a fast backbone. In addition this device is suited to connect a PC to the KNX/EIB network e.g. for ETS programming. The IP address can be obtained by a DHCP server or by manual configuration (ETS) respectively. This device works according to the KNXnet/IP specification using the core, the device management, the tunnelling and the routing part. The KNX IP Router has a filter table and is able to buffer up to 150 telegrams. Technical data Electrical safety - Protection (EN 60529): IP 20 - Safety extra low voltage SELV DC 24 V EMC requirements - Complies with EN 61000-6-2, EN 61000-6-3 and EN 50090-2-2 Environmental requirements - Ambient temp. operating: - 5 ... + 45 °C - Ambient temp. Non-op.: - 25 ... + 70 °C - Rel. humidity (non-condensing): 5 % … 93 % Certification - EIB/KNX CE norm - Complies with the EMC regulations (residential and functional buildings) and low voltage directive Physical specifications - Housing: Plastic - DIN rail mounted device, width: 36 mm - Weight: approx. 100 g - Fire load: approx. 1000 kJ Operating controls - Learning key for EIB/KNX Indicators - Learning-LED (red) - Signal-LED (green) for EIB/KNX - Signal-LED (green) for LAN Ethernet - 10BaseT (10Mbit/s) - Supported internet protocols ARP, ICMP, IGMP, UDP/IP and DHCP Power supply - External supply 12-24V - Alternative: Power-over-Ethernet - Power consumption: < 800 mW Connectors - EIB/KNX connection terminal - LAN RJ-45 socket - Screw connector for power supply Manufacturer: EIBMARKT GmbH Item number: N000402 photographed by EIB3D.COM
...
more
Cookie settings
This website uses cookies that are required for the technical operation of the website and always stored. Other cookies that enhance convenience when using this website, or that are intended for direct marketing or to simplify interaction with other websites and social networks, are only stored with your consent.
Configuration
Technically required
These cookies are required for the basic functions of the shop.
Accept all cookies
Amazon Pay
CSRF token
Cookie settings
Currency change
Customer recognition
Customer-specific caching
FACT-Finder tracking
Individual prices
Reject all cookies
Selected shop
Session
Wish list
Device recognition
Saferpay payments
PayPal payments
IP2location
Listing settings
Trustami
Wishlist
TagManager
Statistics and tracking
Google analytics
Partner program
Custom tracking