Cable grip

Do you know that too? As a precautionary measure, a large number of empty pipes are already installed when fitting out the interior because you already know that the electrical installation will have to be installed there later. But when the time comes, the required power cables cannot be pushed through the empty pipes because they are either squeezed somewhere or have been laid around very tight radii. This can quickly cost a lot of time and nerves. But here good advice does not have to be expensive. With the cable pulling systems from the eibabo online shop, threading the required power lines through existing empty conduits is greatly simplified. On the one hand you get high-quality cable pull-in systems made of fiberglass and on the other hand cable grips for the secure attachment of the cable to the pull-in system. These work in a similar way to a Chinese finger trap. A stainless steel or fiberglass mesh with an eyelet or hook is pushed over a cable end, contracts strongly when pulled and holds the cable in place. The higher the pull, the stronger the holding forces.

Catalogue content:


In this eibabo® catalogue Hand tools > Cable stocking you will find items from the following product groups:

Item overview:

  • Cable grip
  • Cable insertion system
  • Cable lubricant
  • Cable lubricating grease
  • Cable pull-in aid
  • Cable pulling
  • Cable pulling aid
  • Cable pulling device
  • Cable pulling specialist
  • Cable pulling tool
  • Cable retraction
  • Cable retraction spring
  • Cable retraction system
  • Cable stocking
  • Cable tape
  • Collection aid
  • Device for pulling in the cable
  • Devices for pulling in cables
  • Feed system
  • Feeding system
  • Fish tape
  • Installation
  • Lubricant
  • Pull-in aid
  • Retractable spiral
  • Retraction tool
  • Stocking
  • Tool for pulling in the cable


from the following manufacturers:

Manufacturer overview catalogue Cable grip:

  • Cimco
  • Hellermann Tyton
  • Klauke
  • Runpotec


 
Do you know that too? As a precautionary measure, a large number of empty pipes are already installed when fitting out the interior because you already know that the electrical installation will... read more »
Close window
Cable grip
Do you know that too? As a precautionary measure, a large number of empty pipes are already installed when fitting out the interior because you already know that the electrical installation will have to be installed there later. But when the time comes, the required power cables cannot be pushed through the empty pipes because they are either squeezed somewhere or have been laid around very tight radii. This can quickly cost a lot of time and nerves. But here good advice does not have to be expensive. With the cable pulling systems from the eibabo online shop, threading the required power lines through existing empty conduits is greatly simplified. On the one hand you get high-quality cable pull-in systems made of fiberglass and on the other hand cable grips for the secure attachment of the cable to the pull-in system. These work in a similar way to a Chinese finger trap. A stainless steel or fiberglass mesh with an eyelet or hook is pushed over a cable end, contracts strongly when pulled and holds the cable in place. The higher the pull, the stronger the holding forces.

Catalogue content:


In this eibabo® catalogue Hand tools > Cable stocking you will find items from the following product groups:

Item overview:

  • Cable grip
  • Cable insertion system
  • Cable lubricant
  • Cable lubricating grease
  • Cable pull-in aid
  • Cable pulling
  • Cable pulling aid
  • Cable pulling device
  • Cable pulling specialist
  • Cable pulling tool
  • Cable retraction
  • Cable retraction spring
  • Cable retraction system
  • Cable stocking
  • Cable tape
  • Collection aid
  • Device for pulling in the cable
  • Devices for pulling in cables
  • Feed system
  • Feeding system
  • Fish tape
  • Installation
  • Lubricant
  • Pull-in aid
  • Retractable spiral
  • Retraction tool
  • Stocking
  • Tool for pulling in the cable


from the following manufacturers:

Manufacturer overview catalogue Cable grip:

  • Cimco
  • Hellermann Tyton
  • Klauke
  • Runpotec
Close filters
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
from to

1 From 5
No results were found for the filter!
RECOMMENDED
3D
RECOMMENDED
3D
RECOMMENDED
3D
RECOMMENDED
3D
Hellermann Tyton - CS-ACG0415 (VE3) - Cable stocking 4...15mm CS-ACG0415 (VE3)
$56.17 excl. VAT

*

plus shipping
($67.43 RRP***)
Cable stocking 4...15mm
Hellermann Tyton
| CS-ACG0415 (VE3)
RECOMMENDED
Cimco - 14 2501 - Cable pulling grip D=9-12mm - Cable stocking 9...12mm 14 2501
$34.82 excl. VAT

*

plus shipping
($43.32 RRP***)
Cable pulling grip D=9-12mm - Cable stocking 9...12mm
Cimco
| 14 2501
RECOMMENDED
3D
Hellermann Tyton - CS-ACG1630 (VE2) - Cable stocking 16...30mm CS-ACG1630 (VE2)
$65.76 excl. VAT

*

plus shipping
($78.94 RRP***)
Cable stocking 16...30mm
Hellermann Tyton
| CS-ACG1630 (VE2)
RECOMMENDED
Cimco - 14 2502 - Cable pulling grip D=12-15mm - Cable stocking 12...15mm 14 2502
$38.70 excl. VAT

*

plus shipping
($49.46 RRP***)
Cable pulling grip D=12-15mm - Cable stocking 12...15mm
Cimco
| 14 2502
RECOMMENDED
Runpotec - 30040 - Cable pulling stocking with loop 6-9mm 30040
$25.77 excl. VAT

*

Cable pulling stocking with loop 6-9mm
Runpotec
| 30040
RECOMMENDED
RECOMMENDED
Runpotec - 20272 - Cable grip RunpoZ 4-6mm - Cable stocking 20272
$29.15 excl. VAT

*

Cable grip RunpoZ 4-6mm - Cable stocking
Runpotec
| 20272
1 From 5
Viewed from you